Investigation of molar concentration effect on structural,optical, electrical,and photovoltaic properties of spray‐coated Cu2O thin films

High quality copper oxide thin films were prepared by nebulizer spray pyrolysis technique using different concentrations of copper precursor solution. Concentration‐dependent structural, morphological, optical, and electrical properties of the prepared films are discussed. X‐ray diffraction studies done for the samples confirmed that the deposited films are in Cu₂O phase with polycrystalline cubic structure. Atomic force microscopy analysis revealed that all the films are composed of nano sheet shaped grains covering the substrate surface. Optical studies done on the samples showed band gap values 2.42, 2.31, and 2.02 eV for the solution concentration 0.01, 0.05, and 0.1 M, respectively. Photoluminescence spectral analysis showed the emission band at 620 nm confirming the formation of cuprous oxide. Electrical analysis of the films showed p‐type conductivity with a low resistivity 2.19 × 10² Ω.cm and high carrier concentration 16.76 × 10 ¹⁵ cm⁻³ for the molar concentration 0.1 M. In this work, Cu₂O/ZnO heterojunctions were also prepared, and solar cell properties were studied; they were found to show increased open circuit voltage and short circuit current for higher copper concentration.     

A model for crack formation during active solid pyrolysis of a char-forming solid: crack patterns; surface area generation; volatile mass efflux

A model is developed for the formation and propagation of cracks in a material sample that is heated at its top surface, pyrolyses, and then thermally degrades to form char. In this work the sample is heated uniformly over its entire top surface by a hypothetical flame (a heat source). The pyrolysis mechanism is described by a one-step overall reaction that is dependent nonlinearly on the temperature (Arrhenius form). Stresses develop in response to the thermal degradation of the material by means of a shrinkage strain caused by local mass loss during pyrolysis. When the principal stress exceeds a prescribed threshold value, the material forms a local crack. Cracks are found to generally originate at the surface in response to heating, but occasionally they form in the bulk, away from ever-changing material boundaries. The resulting cracks evolve and form patterns whose characteristics are described. Quantities examined in detail are: the crack spacing in the pyrolysis zone; the crack length evolution; the formation and nature of crack loops which are defined as individual cracks that have joined to form loops that are disconnected from the remaining material; the formation of enhanced pyrolysis area; and the impact of all of the former quantities on mass flux. It is determined that the mass flux from the sample can be greatly enhanced over its nominal (non-cracking) counterpart. The mass efflux profile qualitatively resembles those observed in Cone Calorimeter tests.     

丙烯酸盐喷膜防水材料在酸碱浸润和冻融循环条件下的耐久性试验分析

丙烯酸盐喷膜防水材料在酸碱溶液浸润和冻融条件下的耐久性能是该类材料在工程应用中较难回避的实际问题,论文采用酸性介质(0.2%的H2SO4溶液)和碱性介质(0.1%NaOH+饱和Ca(OH)2溶液)对该材料进行饱和浸泡并进行冻融循环后,研究了该材料的吸水性、断裂拉伸强度和拉断伸长率的变化规律。试验结果表明:喷膜防水材料在侵蚀-冻融循环作用下,其拉断伸长率和断裂拉伸强度显著降低,且酸性介质对材料拉伸性能的影响较大;材料耐低温冰冻能力较强,耐高温能力较差。反映出丙烯酸盐喷膜防水材料在低温冰冻和碱性介质中耐久性较好,不建议在高温和酸性介质条件下使用。     

Travelling wave mathematical analysis and efficient numerical resolution for a one-dimensional model of solid propellant combustion

We investigate a model of solid propellant combustion involving surface pyrolysis coupled to finite activation energy gas-phase combustion. Existence and uniqueness of a travelling wave solution are established by extending dynamical system tools classically used for premixed flames, dealing with the additional difficulty arising from the surface regression and pyrolysis. An efficient shooting method allows to solve the problem in phase space without resorting to space discretisation nor fixed-point Newton iterations. The results are compared to solutions from a CFD code developed at ONERA, assessing the efficiency and potential of the method, and the impact of the modelling assumptions is evaluated through parametric studies.     

彩虹自标定方法对混合喷雾比例的原位测量

传统彩虹测量技术标定复杂、精度可重复性差且难以适应密闭空间。一种基于多彩虹谱线自标定方法,可省去原有的标定系统装置,将标定过程内化于对彩虹信号的处理,以水为例的测量偏差仅为0.13%。将该技术应用于混合喷雾液滴组分浓度测量中,探究并优化了参与混合的两种液体组分的方案。实验采用60%乙醇-水混合喷雾,原位测量了混合喷雾场多点组分浓度,测量结果差别可以控制在0.5%以内,表明该方法技术在相关领域的应用潜力。     

HEAT TRANSFER AND PRESSURE DROP FROM LOUVERED SURFACES IN AUTOMOTIVE HEAT EXCHANGERS

An investigation of heat transfer and pressure drop from some louvered surfaces is presented. The test rig and the measuring as well as the data evaluating procedures are described. The measured data are transferred and presented in a nondimenswnal form. The heal transfer data are provided mainly as Stanton numbers versus Reynolds number, and the pressure drop is given as Darcy friction factors versus Reynolds number. For comparing the performance of the various louvered surfaces, the flow area goodness factors and the so-called volume goodness factors are presented. All the louvered surfaces have been found to be more efficient than the corresponding smooth surface. The standard multilouvered fin surfaces were found to be most efficient, but one of the new surfaces also performed very well.     

Flash Vacuum Pyrolysis: Techniques and Reactions

Flash vacuum pyrolysis (FVP) had its beginnings in the 1940s and 1950s, mainly through mass spectrometric detection of pyrolytically formed free radicals. In the 1960s many organic chemists started performing FVP experiments with the purpose of isolating new and interesting compounds and understanding pyrolysis processes. Meanwhile, many different types of apparatus and techniques have been developed, and it is the purpose of this review to present the most important methods as well as a survey of typical reactions and observations that can be achieved with the various techniques. This includes preparative FVP, chemical trapping reactions, matrix isolation, and low temperature spectroscopy of reactive intermediates and unstable molecules, the use of online mass, photoelectron, microwave, and millimeterwave spectroscopies, gas‐phase laser pyrolysis, pulsed pyrolysis with supersonic jet expansion, very low pressure pyrolysis for kinetic investigations, solution‐spray and falling‐solid FVP for involatile compounds, and pyrolysis over solid supports and reagents. Moreover, the combination of FVP with matrix isolation and photochemistry is a powerful tool for investigations of reaction mechanism.     

Thermal stability of ester linkage in the presence of 1,2,3‐Triazole moiety generated by click reaction

The copper(I)‐catalyzed alkyne‐azide cycloaddition (CuAAC), so‐called “click” reaction, is one of most useful synthetic strategies to connect two polymer chains. 1,2,3‐Triazole ring (TA) produced by the click reaction has good thermal and chemical stability. However, we observed that block copolymers synthesized by the click reaction showed thermal degradation to give homopolymers when they are thermally annealed at high temperature, which is required for obtaining equilibrium microdomain structure. To investigate the origin of thermal instability of block copolymers, we synthesized model polystyrenes (PSs) using systematically designed bi‐functional atom transfer radical polymerization (ATRP) initiators containing TA. PS including both ester and TA groups showed thermal decomposition at relatively low temperature (e.g., 140 °C). MALDI‐TOF analysis clearly demonstrated that the cleavage site is the ester group adjacent to TA. We also found that the bromine group located at the polymer chain end plays an important role in pyrolysis of ester groups at low temperature. The pyrolysis occurs by syn‐elimination of the ester group. This result implies that the phase behavior of block copolymer synthesized by click reaction should be carefully investigated when high temperature thermal annealing is required. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 427–436     

Deposition of ZnS thin film by ultrasonic spray pyrolysis: effect of thickness on the crystallographic and electrical properties

Zinc sulfide (ZnS) thin films have been deposited on Si (1 0 0) substrate using ultrasonic spray pyrolysis. X-ray diffraction (XRD) analysis revealed that the films are (0 0 2) preferentially oriented with c-axis-oriented wurtzite structure. The crystallinity has been found to improve with film thickness in the 180–6000 nm range. Film structure has been analyzed by XRD, scanning electron microscope, FTIR, and Raman spectroscopies, while the stoichiometry has been verified by energy-dispersive spectroscopy and particle-induced X-ray emission techniques. Electrical properties of the grown films were characterized by current–voltage and capacitance–voltage measurements where, the films show better conducting behavior at higher thickness.